Current time: 31-05-2016, 05:40 AM Hello There, Guest! LoginRegister)
View New Posts | View Today's Posts

 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
THREE AXIS PNEUMATIC MODERN TRAILERS
08-06-2012, 12:04 PM
Post: #1
THREE AXIS PNEUMATIC MODERN TRAILERS
THREE AXIS PNEUMATIC MODERN TRAILERS



INTRODUCTION


Automation can be achieved through computers, hydraulics, hydraulics, robotics, etc., of these sources, hydraulics form an attractive medium. Automation plays an important role in automobile. Nowadays almost all the automobile vehicle is being atomized in order to product the human being. The automobile vehicle is being atomized for the following reasons.
To achieve high safety
To reduce man power
To increase the efficiency of the vehicle
To reduce the work load
To reduce the fatigue of workers
To high responsibility
Less Maintenance cost



PNEUMATICS

The word ‘pneuma’ comes from Greek and means breather wind. The word pneumatics is the study of air movement and its phenomena is derived from the word pneuma. Today pneumatics is mainly understood to means the application of air as a working medium in industry especially the driving and controlling of machines and equipment.

Pneumatics has for some considerable time between used for carrying out the simplest mechanical tasks in more recent times has played a more important role in the development of pneumatic technology for automation.

Pneumatic systems operate on a supply of compressed air which must be made available in sufficient quantity and at a pressure to suit the capacity of the system. When the pneumatic system is being adopted for the first time, however it wills indeed the necessary to deal with the question of compressed air supply.



SELECTION OF PNEUMATICS

Mechanization is broadly defined as the replacement of manual effort by mechanical power. Pneumatic is an attractive medium for low cost mechanization particularly for sequential (or) repetitive operations. Many factories and plants already have a compressed air system, which is capable of providing the power (or) energy requirements and the control system (although equally pneumatic control systems may be economic and can be advantageously applied to other forms of power).

The main advantage of an all pneumatic system are usually economic and simplicity the latter reducing maintenance to a low level. It can also have out standing advantages in terms of safety.

PRODUCTION OF COMPRESSED AIR

Pneumatic systems operate on a supply of compressed air, which must be made available. In sufficient quantity and at a pressure to suit the capacity of the system. When pneumatic system is being adopted for the first time, however it wills indeed the necessary to deal with the question of compressed air supply.



RECIPROCATING COMPRESSORS

Built for either stationary (or) portable service the reciprocating compressor is by far the most common type. Reciprocating compressors lap be had is sizes from the smallest capacities to deliver more than 500 m³/min. In single stage compressor, the air pressure may be of 6 bar machines discharge of pressure is up to 15 bars. Discharge pressure in the range of 250 bars can be obtained with high pressure reciprocating compressors that of three & four stages.




Attached File(s)
.doc  (##)THREE AXIS PNEUMATIC MODERN TRAILER-WITH OUT MOTOR.doc (Size: 720.5 KB / Downloads: 128)
?
Q


Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Modern VLSI Design seminar addict 1 2,685 13-12-2012 12:44 PM
Last Post: seminar details
  THREE DIMENTIONAL INTEGRATED CIRCUITS seminar details 1 1,088 13-11-2012 12:39 PM
Last Post: seminar details
  Artificial Intelligence Based Three-Phase Unified Power Quality Conditioner project uploader 0 557 11-06-2012 10:38 AM
Last Post: project uploader
  Design and Implementation of PLC-Based Monitoring Control System for Three-Phase seminar details 0 1,187 09-06-2012 12:58 PM
Last Post: seminar details
  Provably Secure Three-Party Authenticated Quantum Key Distribution Protocols seminar paper 0 400 14-03-2012 04:07 PM
Last Post: seminar paper
  Three is the starting point and End point is 5 . seminar paper 0 210 13-03-2012 03:12 PM
Last Post: seminar paper
  FABRICATION OF PNEUMATIC FOOTSTEP LIFTING SYSTEM seminar paper 0 322 12-03-2012 03:23 PM
Last Post: seminar paper
  SPEED CONTROL OF THREE PHASE INDUCTION MOTOR USING ZIGBEE ENTECHNOLOGY seminar paper 0 899 09-03-2012 05:06 PM
Last Post: seminar paper
  Three-Phase System seminar paper 0 328 24-02-2012 03:43 PM
Last Post: seminar paper
  Auto Control of three phase Induction motor seminar addict 1 699 08-02-2012 10:09 AM
Last Post: seminar addict