Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
project help
Post: #1

Hi, pls help for this project topic "Fault Detection and Protection of Induction Motors Using Sensors". If u have any material post it....
Post: #2
Induction motors can be protected using some components, such as timers, contactors, voltage, and current relays. This is the classical method and involves mechanical dynamic parts.Protection of an induction motor (IM) against problems,like overvoltage, overcurrent, overload, overtemperature, and undervoltage, is very important, because it is used widely in industry as an actuator.Computer based and PIC(programmable integrated circuit ) based techniques are available. The computer-based protection method requires an analog-to-digital conversion card, and the PIC-based protection method does not visualize the electrical parameters measured.
New method using PLC
In this method, all contactors, timers, relays, and the conversion card are eliminated. And the voltages, the currents, the speed, and the temperature values of the motor, and the problems occurred in the system, are monitored and warning messages are shown on the computer screen.
The stator current monitoring method for incipient fault detection in induction
machines is widely used for some time.It has advantages such as:
-No additional, potentially unreliable, sensors are necessary, above those
current sensors already used for motor protection;
-Electrical faults, such as broken rotor bars, rotor unbalances, bearing faults and
stator winding faults can be observed; and driven load conditions can be
A fault detection algorithm is available to be used in the condition monitoring of the squirrel-cage induction motors, very widely used in industry all around the world.
This technique depends upon locating by spectrum analysis specific harmonic components in the line current produced of unique rotating flux components caused by faults such as broken rotor bars, air-gap eccentricity and shorted turns in stator windings, etc.
The assumptions taken here are:
-The speed of the machine is constant and known.
- The stator fundamental frequency is constant.
-The load is constant.
-The machine is sufficiently loaded in order to separate the sidebands from the

The exact IEEE paper on the subject can be referred at this link:

You have to have an IEEE membership or your institution must have a subscription to the IEEE Xplore digital library. Or try getting from friends.

Important Note..!

If you are not satisfied with above reply ,..Please


So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: free help with potty training, help cesseilia, help for java, help com, www mataka help marathi com, www help me com, help me in spanish,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Help prashanthyadagiri 2 867 07-02-2014 08:09 PM
Last Post: Guest
  URGENT HELP REQUIRED reetya123 1 372 02-04-2013 12:14 PM
Last Post: computer topic
  Need Help In Electricity Bill Management- Software Engineering Guest 0 598 10-03-2013 11:38 PM
Last Post: Guest
  urgent help : Student Admission System ashokkantsharma 1 1,987 08-03-2013 12:15 PM
Last Post: Guest
  new member so need help pallavi kc 2 1,745 01-10-2012 07:06 AM
Last Post: Stroitelnica
  project help in ece vigneshmc 1 386 12-03-2012 01:11 PM
Last Post: seminar paper
  FINAL YEAR PROJECT IDEAS, need help RJ002 1 666 09-03-2012 11:05 AM
Last Post: seminar paper
  need help Regarding project topic chaitanyapednekar 1 409 06-03-2012 10:59 AM
Last Post: seminar paper
Wink Need help for wireless networking project title ? wcsj90 1 1,074 03-03-2012 01:07 PM
Last Post: seminar paper
  please help.. we are in deep trouble :( madhukarsamak 1 534 02-03-2012 12:29 PM
Last Post: seminar paper